Shijiazhuang Zhongqian Pump Industry Co., Ltd. · Slurry pumps / Spare parts / Technical support
ZQZhongqian PumpZHONGQIAN PUMP
Home/Products/Bearing Assemblies
PRODUCTS · BEARING ASSEMBLIES

Bearing AssembliesThe complete drive end: shaft, bearings, housing and seals as one unit

The bearing assembly is the drive path of the pump and the main diagnostic window: vibration, temperature and noise usually appear here first, although the root cause is often upstream in impeller imbalance, misalignment or lubrication.

Replacing the complete assembly is more reliable than rebuilding on site, particularly without special tools and a clean area. Alignment and impeller clearance must be reset afterwards, or the new assembly will fail in the same way.

Slurry pump bearing assembly
Bearing Assemblies
SCOPE

What this category covers

Part / structureDescription
Bearing housingLocates the bearings and forms the oil and cooling chambers
Bearing setCylindrical roller bearings for radial load, thrust or angular contact for axial
Shaft and sealsTransmits torque; labyrinth and oil seals keep oil in and dirt out
Lubrication and coolingOil level, drain plugs and cooling water connections
MATERIALS

Typical materials for each part

PartFunction in the pumpTypical material
Bearing AssemblyThe bearing assembly supports the shaft under radial and axial loads and governs rotor stability. A cartridge design can be removed as a unit to adjust impeller clearance.Heavy rolling bearings (cylindrical roller plus thrust/angular contact combination) with steel shaft and housing.
Bearing HousingThe bearing housing locates the bearings, forms the lubrication chamber, dissipates heat and maintains bearing concentricity.HT250 grey iron, QT500 ductile iron or cast steel.
ShaftThe pump shaft transmits motor torque and supports the impeller. Adequate strength, stiffness and fatigue resistance are required; straightness directly affects vibration and bearing life.Quality alloy steel or quenched-and-tempered carbon steel, with the seal section protected by a shaft sleeve.
Labyrinth SleeveThe labyrinth sleeve uses a series of tortuous clearances to keep slurry out of the bearing chamber and lubricant in.Cast iron, steel or wear-resistant alloy, often combined with a water thrower.
Grease RetainerThe grease retainer keeps lubricant in and prevents water or slurry from travelling along the shaft into the bearing chamber.Steel, cast iron or a combination with an elastomer lip.
SELECTION

Matching structure and material to the duty

Common combinations; grade choice needs medium temperature, concentration and particle size.

Duty conditionRecommendation
Rising bearing temperatureCheck oil level, cooling and alignment before replacement
Increasing vibrationRule out impeller imbalance and cavitation, then check clearance
No special tools on siteReplace the complete assembly to shorten downtime
Critical standby pumpKeep a complete assembly rather than loose bearings
MATCHING RANGE

Matching series and models

Model pages list construction, code explanation and chart extracts.

AH series
ZJ series
ZGB series
SP series
HH series
G series
DT series
RELATED PARTS

Parts in this category

Each part has its own page with basic number, material and matching range.

FAILURE MODES

How these parts fail and what to do

Judge by wall thickness, clearance and performance, not by months in service.

FAQ

Bearing Assemblies questions

Can just the bearings be replaced?

Yes, with the right tools, a clean area and correct clearance setting. Without them the complete assembly is the safer route.

What bearing temperature is abnormal?

Compare with the manual and bearing maker limits. A rising trend matters more than a single reading.

What must be done after fitting an assembly?

Re-align the coupling, check impeller-to-liner clearance, confirm lubrication and cooling, then monitor vibration and temperature during commissioning.

Inquiry

Send a model or worn-part dimensions

Parts are supplied by basic part number because the same name has different numbers in different frames. Send the pump model, frame code and a photo of the worn part, or the basic number directly.

Ask about Bearing Assemblies

We reply within one business day. You can also call +86 188 0321 2220.

Your details are used for this inquiry only.

Model and spare part identification

Please provide the pump model, nameplate data and duty parameters by phone or email. Performance charts and manuals can be read online.

Click outside or press Esc to close
☎Call✉Email⇄Inquiry