Shijiazhuang Zhongqian Pump Industry Co., Ltd. · Slurry pumps / Spare parts / Technical support
ZQZhongqian PumpZHONGQIAN PUMP
Home/Slurry Pumps/SP / SPR Vertical Sump Pump/100RV-SP
SP / SPR Vertical Sump Pump product sheet
SP / SPR Vertical Sump Pump product sheetModel 100RV-SP
SP / SPR Vertical Sump Pump · Model details

100RV-SP

SP / SPR Vertical Sump Pump

SP / SPR sump pumps keep the motor above the liquid while the pump end is immersed in a pit or tank. No foot valve, priming, shaft seal or seal water is required, suiting fixed submerged duties in settling ponds, sumps and flotation cells.

Vertical / Submersible Slurry PumpVertical, submerged, overhung centrifugal slurry pump
54–289Capacity Q m³/h
5–35Head H m
500–1200Speed r/min
MODEL CODE

Reading the code 100RV-SP

Each segment explained against published industry naming conventions.

FieldMeaning
Discharge bore100 mm
Vertical frame codeRV
Series codeSP vertical sump pump
Model codes are explained against common industry naming conventions for reading the letters and numbers only. Bore sizes, frames, materials and performance of a specific build follow the supplied documents and written confirmation.
CONSTRUCTION & DUTIES

Construction and typical duties

SP / SPR Vertical Sump Pump

Construction

01

The casing is bolted to a support column carrying the bearing housing at its top.

02

An inlet strainer prevents oversized solids from entering the pump.

03

SP has metal wetted parts; SPR has rubber-lined submerged components.

04

Extended shaft builds can be fitted with guide bearings and flush-water piping.

Typical duties

01

Tailings ponds, sumps and tanks

02

Coal washery and power plant settling pits

03

Pit drainage and duties with fluctuating liquid level

Construction drawing
Slurry pump construction drawing
MATERIALS & SEALS

Wetted materials and shaft seals

Wetted materials

SP uses high-chrome wear alloy; SPR has rubber-lined submerged parts for fine-particle and corrosive slurry.

Shaft seal

Submerged designs normally need no shaft seal; column length, guide bearings and flush water are checked against immersion depth.

This section describes general slurry pump principles, selection and maintenance. It does not constitute a commitment regarding particular product parameters, materials, service life or scope of service. Binding values are those in the supplied documentation and in documents confirmed in writing by both parties.
PERFORMANCE DATA

Performance data for 100RV-SP

Clear-water data for this model, full series charts and notes from the manuals.

Model specification and technical parameters

ParameterValue / description
Discharge bore100 mm
Vertical frame codeRV
Series codeSP vertical sump pump
ConstructionVertical, submerged, overhung centrifugal slurry pump
Wetted material optionsSP uses high-chrome wear alloy; SPR has rubber-lined submerged parts for fine-particle and corrosive slurry.
Shaft seal optionsSubmerged designs normally need no shaft seal; column length, guide bearings and flush water are checked against immersion depth.
Published series coverageTypical coverage: discharge bores about 40-300 mm and head up to about 40 m.

100RV-SP · rows in SP Series Vertical Pump Chart · table 1 (1)

ModelMax. power kWQ m³/hQ L/sH mn r/minMax. eff. %Impeller mm
100RV-SP7554-28915-80.35-35500-120056370

Full performance charts for this series

Complete clear-water performance data for this series. Click to expand; tables scroll horizontally.

SP Series Vertical Pump Chart · table 110 rows
ModelMax. power kWQ m³/hQ L/sH mn r/minMax. eff. %Impeller mm
40PV-SP1519.44-43.25.4-1.24.5-28.51000-220040188
40PV-SPR1517.28-39.64.8-114-261000-220040188
60QV-SP3023.4-1116.5-30.85-29.5700-150050280
60QV-SPR3022.5-1056.25-29.155.5-30.5700-150051280
100RV-SP7554-28915-80.35-35500-120056370
100RV-SPR7564.8-28518-79.27.5-36600-120062370
150SV-SP110108-479.630-133.18.5-40500-100052450
200SV-SP110189-891152.5-247.56.5-37400-85064520
250TV-SP200261-108972.5-302.57.5-33.5400-75060575
300TV-SP200288-126780-3526.5-33350-70050610
Clear-water performance data for reference only; binding values follow the supplied technical documents and written confirmation.
FROM THE MANUAL

Notes from the product manuals

Compiled from the AH / L / G, SP, ZJ and ZGB pump manuals, with links to the full texts.

General construction, installation and operation

01 · Overview and scope

Horizontal slurry pumps are overhung centrifugal pumps for abrasive or corrosive slurry, widely used in metallurgy, mining, petrochemical, coal, power, dredging, building materials and municipal works. Families cover heavy duty (AH, HH), light duty (L), gravel / dredging (D, G) and rubber-lined (AHR, LR, MR) builds. Pumps may be staged in series within the allowable working pressure.

02 · Construction

Heavy duty AH and HH pumps use a double casing: an outer pressure-retaining casing and cover in grey or ductile iron, vertically split and bolted, plus replaceable wear liners (impeller, volute liner, throat bush and frame plate liner) in metal or rubber. The discharge can be rotated in eight positions at 45 degree intervals. D and G gravel pumps use a single casing with all wetted parts in wear-resistant metal. Apart from the wet end, all horizontal types share the same frame and bearing assembly, with a large-diameter shaft and short overhang.

03 · Assembly and installation

Preheat bearing inner rings to no more than 120 C during assembly and seat them firmly against the shaft shoulder or grease retainer. Inner rings, outer rings and spacers of double-row tapered roller bearings form a matched set and must not be interchanged. Wet-end assembly order: seals, frame plate liner with its locating nuts, impeller, volute liner clamped in place, then throat bush and cover plate. Lift crated pumps by the marked sling points without shock or excessive tilt; lifting eyes on the casing are for dismantling the casing only, never for lifting the complete pump.

04 · Shaft seal and lubrication

Three shaft seal arrangements are common: expeller, packed gland and mechanical seal. The expeller seal suits single-stage pumps (or the first stage of a series set) where inlet positive pressure is below 10 percent of discharge pressure; it needs no seal water and does not dilute the slurry. A packed gland is simple to service but requires seal water. A mechanical seal gives the best sealing and requires cooling water. A packed gland comprises the stuffing box, shaft sleeve, spacer, O-rings, packing, packing spacer, lantern ring and gland. Bearings are grease or oil lubricated, with oil lubrication preferred for high temperature or large pumps.

05 · Start-up and operation

Before start-up check that foundation and coupling bolts are tight, turn the shaft by hand in the direction of rotation without rubbing, verify motor rotation against the arrow on the casing, and align the V-belts square to the pulleys. Starting on clean water is preferable before slurry is introduced. During operation watch the instruments for flow, velocity and current and correct any abnormality. Where possible flush with clean water before stopping, then stop the pump before closing the valve. For vertical sump pumps, turn on the guide bearing flush water five minutes before starting and close it five minutes after stopping.

06 · Maintenance and faults

Check impeller-to-throatbush clearance, bearing temperature and lubrication, seal water pressure and flow, and wear of wetted parts on a regular basis. A worn impeller reduces flow and head and raises vibration and noise, so adjust the clearance or replace the wear parts. Typical faults are insufficient flow or head, bearing overheating, vibration, seal leakage and cavitation, usually caused by blockages, wrong rotation, low speed, air ingress on the suction side, inadequate NPSH or loss of dynamic balance. Record basic part numbers and material suffixes and verify them against the pump model and supplied documents.

Series-specific notes for SP / SPR Vertical Sump Pump

01

SP(R) pumps are vertical centrifugal slurry pumps working immersed in a pit or sump. SP uses metal wetted parts and shaft; SPR has rubber-lined immersed components.

02

The bearing housing sits on top of the support column with a double-row tapered roller bearing at the pump end and a single-row cylindrical roller bearing at the drive end. A split mounting plate and an inlet strainer keep large solids out.

03

No clearance adjustment is needed during bearing assembly, but the assembled end clearance should be checked against the manual (PV 0.074–0.160 mm, QV 0.114–0.208 mm and so on). Run guide bearing flush water for five minutes before starting.

04

The liquid level must not fall below the minimum stated in the manual. Flush with clean water before stopping and close the guide bearing flush water five minutes later.

Source text excerpts

Original manual text

Extracts from the original manuals are shown in the Chinese edition; the full texts are available via the links below.

Read the source documents online

WEAR PARTS

Wear parts for this series

Open each part page for function, material and replacement notes.

INQUIRY

100RV-SP — quotation and part check

Send the model or worn-part dimensions, or call +86 188 0321 2220 / email sale@pumpq.com.

Request a price

We reply within one business day. You can also call +86 188 0321 2220.

Your details are used for this inquiry only.

Model and spare part identification

Please provide the pump model, nameplate data and duty parameters by phone or email. Performance charts and manuals can be read online.

Click outside or press Esc to close
☎Call✉Email⇄Inquiry