Shijiazhuang Zhongqian Pump Industry Co., Ltd. · Slurry pumps / Spare parts / Technical support
ZQZhongqian PumpZHONGQIAN PUMP
Home/Products/Slurry Pump Impellers
PRODUCTS · SLURRY PUMP IMPELLERS

Slurry Pump ImpellersThe only energy-transferring part: diameter and material decide flow, head and life

The impeller is the only component that does work on the slurry. Motor torque reaches it through the shaft, and its diameter, vane number and passage width set flow, head, efficiency and solids handling capability.

Because it carries the whole energy transfer, the impeller is usually the first part to wear. Closed and semi-open designs, and metal, rubber or polyurethane materials, are selected against particle size and pH rather than price.

Rubber and metal slurry pump impellers
Slurry Pump Impellers
SCOPE

What this category covers

Part / structureDescription
Closed impellerShrouded passages, higher efficiency, for fine to medium particles
Semi-open impellerNo front shroud, wider passage, for coarse or blocking solids
Metal impellerHigh-chrome alloy, resistant to coarse particle erosion
Rubber impellerRubber moulded on a steel core, for fine particles and mild corrosion
MATERIALS

Typical materials for each part

PartFunction in the pumpTypical material
ImpellerThe impeller is the energy-converting core of a slurry pump. It transfers motor torque to the slurry and determines flow, head and efficiency; vanes are thick and passages wide so solids can pass.Mainly high-chrome wear alloy (A05 / Cr26 / Cr27); rubber or polyurethane for fine, mildly corrosive or rounded particles, and duplex stainless steels for severe corrosion.
Impeller Release RingThe impeller release ring provides a bearing surface for removal, protecting impeller threads and the shaft end during on-site wear part changes.Quenched-and-tempered steel or stainless steel with sound threads.
Lock NutThe lock nut secures the impeller, bearings or coupling components against loosening from vibration and shock.Carbon or stainless steel with a locking feature.
Front LinerThe front liner (throatbush) protects the suction-side cover, forms the impeller inlet sealing face and controls inlet recirculation and suction-side wear.High-chrome wear alloy or rubber; metal parts are preferred for fine but highly abrasive solids.
Frame Plate LinerThe frame plate liner protects the drive-side casing from erosion and forms the sealing chamber with the impeller rear shroud, directly affecting volumetric efficiency.High-chrome wear alloy, rubber lining or wear/corrosion-resistant alloy, matched to the impeller material.
SELECTION

Matching structure and material to the duty

Common combinations; grade choice needs medium temperature, concentration and particle size.

Duty conditionRecommendation
Coarse, angular solidsHigh-chrome alloy with thick vanes and wide passages
Fine, mildly corrosive, alkalineRubber impeller, often longer life than standard metal
Mixed dutyMetal impeller with rubber liners, selected part by part
High head, efficiency focusLarge closed impeller operating near the BEP
MATCHING RANGE

Matching series and models

Model pages list construction, code explanation and chart extracts.

AH series
ZJ series
ZGB series
SP series
HH series
G series
DT series
RELATED PARTS

Parts in this category

Each part has its own page with basic number, material and matching range.

FAILURE MODES

How these parts fail and what to do

Judge by wall thickness, clearance and performance, not by months in service.

FAQ

Slurry Pump Impellers questions

When must an impeller be replaced?

By remaining wall thickness or head loss. Perforated vanes, grooves approaching half the wall thickness, or a clearance that can no longer be restored mean replacement.

Should liners be replaced with the impeller?

Not always, but they must be inspected together. The impeller-to-liner clearance governs volumetric efficiency, so a grooved liner will not restore performance.

Can a worn impeller be rebalanced?

Metal impellers can, but balancing only delays replacement; it does not restore hydraulic performance once the walls have thinned.

Inquiry

Send a model or worn-part dimensions

Parts are supplied by basic part number because the same name has different numbers in different frames. Send the pump model, frame code and a photo of the worn part, or the basic number directly.

Ask about Slurry Pump Impellers

We reply within one business day. You can also call +86 188 0321 2220.

Your details are used for this inquiry only.

Model and spare part identification

Please provide the pump model, nameplate data and duty parameters by phone or email. Performance charts and manuals can be read online.

Click outside or press Esc to close
☎Call✉Email⇄Inquiry