Rubber wetted parts are often treated as a cheap substitute. In the right duty they outlast metal several times over, weigh less, fit faster and run quieter. The key is to use them where they belong: fine particles, mild acids and alkalis, moderate temperature.
A practical threshold is particle size. Within roughly 10 mm, with rounded particles and pH from mildly acidic to alkaline, rubber is usually the lower cost per hour. Above that, or at elevated temperature, high-chrome alloy is the correct route.

| Part / structure | Description |
|---|---|
| Rubber impeller | Rubber moulded over a steel core for fine, mildly corrosive slurry |
| Rubber volute liner | Forms the flow passage; about half the weight of a metal liner |
| Rubber cover plate liner | Front and frame plate liners matched to the rubber volute |
| Rubber-lined casing | Casing with an integrally bonded rubber lining |
| Part | Function in the pump | Typical material |
|---|---|---|
| Impeller | The impeller is the energy-converting core of a slurry pump. It transfers motor torque to the slurry and determines flow, head and efficiency; vanes are thick and passages wide so solids can pass. | Mainly high-chrome wear alloy (A05 / Cr26 / Cr27); rubber or polyurethane for fine, mildly corrosive or rounded particles, and duplex stainless steels for severe corrosion. |
| Volute Liner | The volute liner collects slurry discharged by the impeller and converts velocity energy into pressure. It is the key replaceable wear liner in a double-casing pump. | High-chrome wear alloy, wear-resistant rubber or polyurethane: metal for coarse abrasive solids, rubber for corrosive fine particles. |
| Front Liner | The front liner (throatbush) protects the suction-side cover, forms the impeller inlet sealing face and controls inlet recirculation and suction-side wear. | High-chrome wear alloy or rubber; metal parts are preferred for fine but highly abrasive solids. |
| Frame Plate Liner | The frame plate liner protects the drive-side casing from erosion and forms the sealing chamber with the impeller rear shroud, directly affecting volumetric efficiency. | High-chrome wear alloy, rubber lining or wear/corrosion-resistant alloy, matched to the impeller material. |
| Pump Casing | The casing carries system pressure and locates the pump end and frame. In a double-casing pump it is the outer pressure shell; in a single-casing gravel pump it also serves as the wear body. | Ductile iron, cast steel or wear-resistant alloy; in double-casing pumps the inner surface is protected by replaceable liners. |
Common combinations; grade choice needs medium temperature, concentration and particle size.
| Duty condition | Recommendation |
|---|---|
| Fine (<10 mm), rounded | Rubber impeller, volute liner and liners as a set |
| pH 2–12, mild chemicals | Rubber outperforms standard metal; confirm the compound |
| Sharp coarse solids or >70°C | Use high-chrome alloy; rubber will tear or age |
| Low noise, frequent handling | Rubber parts are lighter and faster to change |
Model pages list construction, code explanation and chart extracts.
Each part has its own page with basic number, material and matching range.

Mainly high-chrome wear alloy (A05 / Cr26 / Cr27); rubber or p…

High-chrome wear alloy, wear-resistant rubber or polyurethane:…

High-chrome wear alloy or rubber; metal parts are preferred fo…

High-chrome wear alloy, rubber lining or wear/corrosion-resist…

Ductile iron, cast steel or wear-resistant alloy; in double-ca…
Judge by wall thickness, clearance and performance, not by months in service.
The unit price is usually lower and the weight is less, but the real comparison is cost per operating hour. In fine corrosive duty rubber often lasts longer.
It can, provided tip speed and temperature rise are within the compound limits, which must be confirmed for the application.
Check lining thickness, cuts, blisters and sealing face distortion. Replace when less than half the original thickness remains or a through cut appears.
Parts are supplied by basic part number because the same name has different numbers in different frames. Send the pump model, frame code and a photo of the worn part, or the basic number directly.
We reply within one business day. You can also call +86 188 0321 2220.
Please provide the pump model, nameplate data and duty parameters by phone or email. Performance charts and manuals can be read online.