Shijiazhuang Zhongqian Pump Industry Co., Ltd. · Slurry pumps / Spare parts / Technical support
ZQZhongqian PumpZHONGQIAN PUMP
Home/Slurry Pumps/SYA / ZJE Filter Press Feed Pump/65SYA75-30
Horizontal filter-feed pump, representative view
SYA / ZJE Filter Press Feed Pump product sheetModel 65SYA75-30
SYA / ZJE Filter Press Feed Pump · Model details

65SYA75-30

SYA / ZJE Filter Press Feed Pump

SYA / ZJE pumps are designed for filter press feeding, where flow falls and pressure rises as the press fills. They must run stably across a wide duty range; twin-impeller or two-stage builds cover the higher pressure at the end of the cycle.

Horizontal Slurry PumpHorizontal filter press feed pump
MODEL CODE

Reading the code 65SYA75-30

Each segment explained against published industry naming conventions.

FieldMeaning
Bore designation65 mm
Series codeSYA filter press feed pump
Flow section75 (rated flow designation)
Head / power section30 (check against the manufacturer code)
Model codes are explained against common industry naming conventions for reading the letters and numbers only. Bore sizes, frames, materials and performance of a specific build follow the supplied documents and written confirmation.
CONSTRUCTION & DUTIES

Construction and typical duties

SYA / ZJE Filter Press Feed Pump

Construction

01

Follows the filter press cycle from high flow/low pressure to low flow/high pressure.

02

Twin-impeller or two-stage builds raise pressure late in the cycle.

03

Wetted parts in metal or rubber according to abrasion and corrosion.

04

Usually paired with a filter press; flow is checked against chamber volume and filling time.

Typical duties

01

Filter press feed and sludge dewatering

02

Tailings dry stacking and concentrate dewatering

03

Chemical, ceramic and coal filter-cake processes

Construction drawing
Slurry pump construction drawing
MATERIALS & SEALS

Wetted materials and shaft seals

Wetted materials

High-chrome wear alloy, rubber lining or wear/corrosion-resistant alloys, selected against slurry composition.

Shaft seal

Packing or mechanical seals; seal reliability during the high-pressure phase needs attention.

This section describes general slurry pump principles, selection and maintenance. It does not constitute a commitment regarding particular product parameters, materials, service life or scope of service. Binding values are those in the supplied documentation and in documents confirmed in writing by both parties.
PERFORMANCE DATA

Performance data for 65SYA75-30

Clear-water data for this model, full series charts and notes from the manuals.

Model specification and technical parameters

ParameterValue / description
Bore designation65 mm
Series codeSYA filter press feed pump
Flow section75 (rated flow designation)
Head / power section30 (check against the manufacturer code)
ConstructionHorizontal filter press feed pump
Wetted material optionsHigh-chrome wear alloy, rubber lining or wear/corrosion-resistant alloys, selected against slurry composition.
Shaft seal optionsPacking or mechanical seals; seal reliability during the high-pressure phase needs attention.
Published series coveragePublished specifications are stated as flow, head and motor power combinations; exact values follow written confirmation.

About the performance data for this model

Clear-water data for this particular model is not listed separately; the common coverage of its series is given below for reference only. Expand the full series charts where available. Binding values follow the supplied documents and written confirmation.

Commonly published series coverage

Published specifications are stated as flow, head and motor power combinations; exact values follow written confirmation.

Full performance charts for this series

Complete clear-water performance data for this series. Click to expand; tables scroll horizontally.

ZJE Filter Press Feed Pump Chart · table 112 rows
Modeln r/minQ m³/hH mShaft power kWReference motorPower kW
65ZJE-Ⅱ148027.5 41.4 55.2 69.0 80.076.0 72.2 66.1 56.0 43.522.3Y225S-430
65ZJE-Ⅱ148027.5 41.4 55.2 69.0 80.076.0 72.2 66.1 56.0 43.522.3Y225S-437
80ZJE-Ⅱ148040.0 60.0 80.0 100 11576.0 72.2 66.1 56.0 43.532Y225S-437
80ZJE-Ⅱ148040.0 60.0 80.0 100 11576.0 72.2 66.1 56.0 43.532Y225M-445
100ZJE-Ⅱ148056.0 85.0 113 150 16973.3 69.0 62.5 51.2 44.049Y225M-445
100ZJE-Ⅱ148056.0 85.0 113 150 16973.3 69.0 62.5 51.2 44.049Y225M-455
125ZJE-Ⅱ148070.0 105 140 186 24573.5 71.6 68.6 61.9 48.562.5Y225M-455
125ZJE-Ⅱ148070.0 105 140 186 24573.5 71.6 68.6 61.9 48.562.5Y280S-475
125ZJE-Ⅱ148079.7 119 159 211 27980.0 78.0 74.8 67.5 52.978.2Y280S-475
125ZJE-Ⅱ148079.7 119 159 211 27980.0 78.0 74.8 67.5 52.978.2Y280M-490
125ZJE-Ⅱ148058.0 87.0 116 154 20391.8 89.1 85.7 77.3 60.664.7Y280S-475
125ZJE-Ⅱ148058.0 87.0 116 154 20391.8 89.1 85.7 77.3 60.664.7Y280M-490
ZJE Filter Press Feed Pump Chart · table 218 rows
ModelMotor power kWQ m³/hH mn r/minEff. %NPSH mMax. particle mmWeight kg
200ZJG-B45Y280M-4 90KW27272.9148065.310.7281731
200ZJG-B45Y315M1-4 132KW44757.514806810.7281731
200ZJG-B45Y315L1-4 160KW5384714806210.7281731
200ZJG-B45Y226M-6 30KW1803298065.34.7281731
200ZJG-B45Y250M-6 37KW29625.2980684.7281731
200ZJG-B45Y250M-6 37KW35620.6980624.7281731
150ZJG-B45Y280M-4 90KW22372.51480587.325.61576
150ZJG-B45Y315S-4 110KW372601480657.325.61576
150ZJG-B45Y3154S-4 110KW458491480607.325.61576
150ZJG-B45Y225M-6 30KW14732980583.225.61576
150ZJG-B45Y250M-6 37KW24726.3980653.225.61576
150ZJG-B45Y250M-6 37KW30321980603.225.61576
100ZJG-B42Y225M-4 45KW9670.7148051.92.8181085
100ZJG-B42Y250M-4 55KW14963.81480612.8181085
100ZJG-B42Y280S-4 75KW205561480632.8181085
100ZJG-B42Y180L-6 15KW643198051.91.8181085
100ZJG-B42Y200L1-6 18.5KW9928980611.8181085
100ZJG-B42Y200L2-6 22KW13625980631.8181085
ZJE Filter Press Feed Pump Chart · table 310 rows
ModelQ m³/hH mn r/minMotor power kWFilter press m²
50ZJE65-2220-7030-6514502240-60
50ZJE75-3020-7035-7514503040-70
50ZJE76-3720-10030-7614503760-120
65ZJE80-4535-12535-8014504560-120
80ZJE65-4540-14030-6514504580-150
80ZJE75-5550-16035-7514505580-150
100ZJE75-7570-24530-75145075100-200
100ZJE80-9050-28035-80145090100-200
125ZJE70-9080-30030-70145090150-250
150ZJE75-11080-33035-751450110150-300
Clear-water performance data for reference only; binding values follow the supplied technical documents and written confirmation.
FROM THE MANUAL

Notes from the product manuals

Compiled from the AH / L / G, SP, ZJ and ZGB pump manuals, with links to the full texts.

General construction, installation and operation

01 · Overview and scope

Horizontal slurry pumps are overhung centrifugal pumps for abrasive or corrosive slurry, widely used in metallurgy, mining, petrochemical, coal, power, dredging, building materials and municipal works. Families cover heavy duty (AH, HH), light duty (L), gravel / dredging (D, G) and rubber-lined (AHR, LR, MR) builds. Pumps may be staged in series within the allowable working pressure.

02 · Construction

Heavy duty AH and HH pumps use a double casing: an outer pressure-retaining casing and cover in grey or ductile iron, vertically split and bolted, plus replaceable wear liners (impeller, volute liner, throat bush and frame plate liner) in metal or rubber. The discharge can be rotated in eight positions at 45 degree intervals. D and G gravel pumps use a single casing with all wetted parts in wear-resistant metal. Apart from the wet end, all horizontal types share the same frame and bearing assembly, with a large-diameter shaft and short overhang.

03 · Assembly and installation

Preheat bearing inner rings to no more than 120 C during assembly and seat them firmly against the shaft shoulder or grease retainer. Inner rings, outer rings and spacers of double-row tapered roller bearings form a matched set and must not be interchanged. Wet-end assembly order: seals, frame plate liner with its locating nuts, impeller, volute liner clamped in place, then throat bush and cover plate. Lift crated pumps by the marked sling points without shock or excessive tilt; lifting eyes on the casing are for dismantling the casing only, never for lifting the complete pump.

04 · Shaft seal and lubrication

Three shaft seal arrangements are common: expeller, packed gland and mechanical seal. The expeller seal suits single-stage pumps (or the first stage of a series set) where inlet positive pressure is below 10 percent of discharge pressure; it needs no seal water and does not dilute the slurry. A packed gland is simple to service but requires seal water. A mechanical seal gives the best sealing and requires cooling water. A packed gland comprises the stuffing box, shaft sleeve, spacer, O-rings, packing, packing spacer, lantern ring and gland. Bearings are grease or oil lubricated, with oil lubrication preferred for high temperature or large pumps.

05 · Start-up and operation

Before start-up check that foundation and coupling bolts are tight, turn the shaft by hand in the direction of rotation without rubbing, verify motor rotation against the arrow on the casing, and align the V-belts square to the pulleys. Starting on clean water is preferable before slurry is introduced. During operation watch the instruments for flow, velocity and current and correct any abnormality. Where possible flush with clean water before stopping, then stop the pump before closing the valve. For vertical sump pumps, turn on the guide bearing flush water five minutes before starting and close it five minutes after stopping.

06 · Maintenance and faults

Check impeller-to-throatbush clearance, bearing temperature and lubrication, seal water pressure and flow, and wear of wetted parts on a regular basis. A worn impeller reduces flow and head and raises vibration and noise, so adjust the clearance or replace the wear parts. Typical faults are insufficient flow or head, bearing overheating, vibration, seal leakage and cavitation, usually caused by blockages, wrong rotation, low speed, air ingress on the suction side, inadequate NPSH or loss of dynamic balance. Record basic part numbers and material suffixes and verify them against the pump model and supplied documents.

Series-specific notes for SYA / ZJE Filter Press Feed Pump

01

A filter press feed pump delivers high flow at low pressure early in the cycle and low flow at high pressure later, so the full flow–head curve and motor power must be matched across the whole cycle.

02

ZJE charts list flow, head, speed, power and matched filter press area, allowing a first pump selection by filtration area.

Source text excerpts

Original manual text

Extracts from the original manuals are shown in the Chinese edition; the full texts are available via the links below.

Read the source documents online

WEAR PARTS

Wear parts for this series

Open each part page for function, material and replacement notes.

INQUIRY

65SYA75-30 — quotation and part check

Send the model or worn-part dimensions, or call +86 188 0321 2220 / email sale@pumpq.com.

Request a price

We reply within one business day. You can also call +86 188 0321 2220.

Your details are used for this inquiry only.

Model and spare part identification

Please provide the pump model, nameplate data and duty parameters by phone or email. Performance charts and manuals can be read online.

Click outside or press Esc to close
☎Call✉Email⇄Inquiry