Shijiazhuang Zhongqian Pump Industry Co., Ltd. · Slurry pumps / Spare parts / Technical support
ZQZhongqian PumpZHONGQIAN PUMP
SPARE PARTS

Slurry Pump Spare PartsWetted parts · seals · drive components

Identify parts by basic number

Impeller, frame plate liner, casing, shaft sleeve and more, each with basic number, bilingual name, location, materials (high-chrome alloy / rubber / 3Cr13), wear signs and service notes, with links to matching pump models.

Slurry pump casing
Casing photograph
KEY PARTS

Key spare parts

Four wetted and seal parts most often identified, with materials and basic numbers on their own pages.

PART INDEX

All spare parts

Switch between wetted, seal, drive and fastener groups to see materials and basic numbers.

Wetted parts contact the slurry directly and wear fastest. Impeller, volute liner, front liner and frame plate liner are normally evaluated as a set to maintain running clearances.
Shaft seal parts control leakage between the pump chamber and the atmosphere. Packing, expeller and mechanical seal options have different seal-water requirements; check sleeve grooves and lantern ring holes first during service.
Bearing and drive parts support the rotor and transmit power. Most are not wear parts; attention focuses on lubrication, temperature rise, vibration and alignment, with service intervals per the manual.
Fasteners and small accessories are minor in size but critical to assembly reliability. Replace locking elements after disassembly and tighten diagonally, in stages, to the specified torque.
MATERIALS

Wetted part materials

Balance abrasion and corrosion resistance against the medium.

MaterialTypical dutySelection notes
High chrome alloy Cr26 / Cr27 / Cr30Coarse, sharp, highly abrasive ore slurry, tailings and ashVery hard and abrasion resistant; relatively brittle and not suited to large stray impacts
Natural / synthetic wear-resistant rubberFine particles, mildly acidic or alkaline corrosive slurry; noise and vibration dampingElastic and resistant to fine-particle cutting; vulnerable to sharp coarse solids and high temperature - check the temperature limit
Duplex stainless / high-nickel alloyStrongly corrosive, chloride-bearing or high-temperature specialty slurriesCorrosion resistance first; weigh service life and cost against abrasiveness
Polyurethane / ceramic compositeFine but highly abrasive particles, or lightweight wear solutionsLightweight and wear resistant, higher cost; always verify part number and dimensions
This section describes general slurry pump principles, selection and maintenance. It does not constitute a commitment regarding particular product parameters, materials, service life or scope of service. Binding values are those in the supplied documentation and in documents confirmed in writing by both parties.
SHAFT SEALS

Common shaft seal arrangements

The seal option determines seal-water demand and the wear part set.

Gland Packing

填料密封

Simple and easy to service on site. A small controlled drip lubricates and cools the packing, so a reliable sealing-water supply is needed. Common on general duties.

Expeller + Packing

副叶轮 + 填料组合密封

The expeller generates back pressure to balance the pressure at the seal, reducing sealing-water demand. Widely used on tailings and ash duties.

Mechanical Seal

机械密封

Very low leakage for duties where spillage is unacceptable or the medium is hazardous; demands accurate installation and a clean flush-water system.

DRAWINGS

Construction and exploded views

Use the drawings to identify part positions and assembly relationships.

Exploded view
Exploded view
Horizontal construction
Horizontal construction
Vertical construction
Vertical construction
Gravel pump construction
Gravel pump construction
Metal vs. rubber parts
Metal vs. rubber parts
AH dimension drawing
AH dimension drawing
CHECKLIST

Part identification checklist

Following this order before ordering reduces mismatches.

01

Record the pump model and nameplate data

Then open the part page for location and wear notes.

02

Confirm wetted material (metal / rubber)

Then open the part page for location and wear notes.

03

Check the part basic number and frame code

Then open the part page for location and wear notes.

04

Measure impeller-to-liner clearances

Then open the part page for location and wear notes.

05

Inspect sleeve grooves and seal-water system

Then open the part page for location and wear notes.

06

Evaluate wetted part replacement as a set

Then open the part page for location and wear notes.

Model and spare part identification

Please provide the pump model, nameplate data and duty parameters by phone or email. Performance charts and manuals can be read online.

Click outside or press Esc to close
☎Call✉Email⇄Inquiry