
The stuffing box houses packing, the lantern ring and the gland, forming the packing seal chamber and admitting seal water for cooling, lubrication and flushing.
The stuffing box houses packing, the lantern ring and the gland, forming the packing seal chamber and admitting seal water for cooling, lubrication and flushing.
On the drive side of the pump end around the shaft sleeve, assembled with the gland and lantern ring.
Basic number, common full part numbers, the complete code index and model-by-model references.
Stuffing box
B078C078Stuffing box basic number 078, forming the seal assembly with 044 gland, 063 lantern ring, 111 packing and 117 spacer.
Part names link to their own pages; the current part is highlighted.
| Basic no. | Part name | Group |
|---|---|---|
001 | Adjusting bolt | Drive |
003 | Bearing frame | Drive |
004 | Bearing housing | Drive |
005 | Bearing assembly / rotor | Drive |
009 | Bearing | Drive |
011 | Clamp washer | Fasteners |
012 | Clamp bolt | Fasteners |
013 | Cover plate | Wetted |
015 | Cover plate stud | Fasteners |
018 | Front rubber sheath | Wetted |
023 | Front sheath stud | Fasteners |
024 | End cover | Drive |
025 | End cover gasket | Seal |
026 | Frame plate liner bolt | Fasteners |
027 | End cover adjusting nut | Fasteners |
028 | Expeller | Seal |
029 | Relief cover | Seal |
032 | Casing / pump body | Wetted |
034 | Casing bolt | Fasteners |
036 | Rear rubber sheath | Wetted |
039 | Rear sheath stud | Fasteners |
040 | Frame plate liner bolt | Fasteners |
041 | Frame plate liner insert | Wetted |
043 | Rear sheath | Wetted |
044 | Split gland | Seal |
045 | Gland bolt | Fasteners |
046 | Grease retainer | Drive |
061 | Imperial round nut | Fasteners |
062 | Labyrinth sleeve | Seal |
063 | Lantern ring | Seal |
064 | O-ring | Seal |
067 | Packing spacer | Seal |
073 | Shaft | Drive |
075 / 076 | Shaft sleeve / long sleeve | Seal |
078 | Stuffing box | Seal |
080 | Register gasket | Fasteners |
081 | Locating plate | Drive |
083 | Throatbush | Wetted |
085 | Locating wedge | Wetted |
089 | Bearing seal ring | Drive |
090 | Lip seal ring | Seal |
108 | Labyrinth ring | Seal |
109 | O-ring | Seal |
110 | Volute liner | Wetted |
111 | Packing | Seal |
117 | Spacer | Drive |
118 | Front lantern ring | Seal |
122 | Gasket | Fasteners |
124 | Volute liner gasket | Wetted |
125 | Frame plate liner gasket | Wetted |
126 | Gland stud | Fasteners |
132 | Discharge gasket | Wetted |
138 | Oil cup seat | Drive |
147 | Impeller | Wetted |
Prefixes vary with pump model and frame. Both model and part names link to their own pages.
| Impeller | E4147 |
| Volute liner | E4110 |
| Throatbush | E4083 |
| Frame plate liner | E4041 |
| Shaft sleeve | D075 |
| Lantern ring | D063 |
| Gland | D044 |
| Relief cover | DAM029 |
| Expeller | DAM028 |
| Impeller | F6147 |
| Volute liner | F6110 |
| Throatbush | F6083 |
| Frame plate liner | F6041 |
| Shaft sleeve | E075 |
| Spacer | EAM117 |
| Front lantern ring | E118 |
| Packing | F111 |
| Impeller | FAM8147 |
| Volute liner | G8110 |
| Throatbush | G8083 |
| Frame plate liner | G8041 |
| Shaft sleeve | FAM075 |
| Spacer | G117 |
| Front lantern ring | G118 |
| Impeller | G8147 |
| Volute liner | G8110 |
| Throatbush | G8083 |
| Frame plate liner | G8041 |
| Long shaft sleeve | SH076 |
| Front lantern ring | G118 |
| Impeller | EH3147 |
| Volute liner | EH3110 |
| Throatbush | EH3083 |
| Frame plate liner | EH3041 |
| Shaft sleeve | E075 |
| Spacer | EAM117 |
| Front lantern ring | E118 |
| Impeller | D3147 |
| Volute liner | D3110 |
| Throatbush | D3083 |
| Frame plate liner | D3041 |
| Impeller | THG30137LPT1A05 |
| Volute | GHG30131A05 |
| Throatbush | GHG30013LPT1A05 |
| Frame plate liner | GHG30041A05 |
Shaft seal parts control leakage between the pump chamber and the atmosphere. Packing, expeller and mechanical seal options have different seal-water requirements; check sleeve grooves and lantern ring holes first during service.
Cast iron, cast steel or wear/corrosion-resistant alloy, with the bore matched to the shaft sleeve.
| Material | Typical duty | Selection notes |
|---|---|---|
| High chrome alloy Cr26 / Cr27 / Cr30 | Coarse, sharp, highly abrasive ore slurry, tailings and ash | Very hard and abrasion resistant; relatively brittle and not suited to large stray impacts |
| Natural / synthetic wear-resistant rubber | Fine particles, mildly acidic or alkaline corrosive slurry; noise and vibration damping | Elastic and resistant to fine-particle cutting; vulnerable to sharp coarse solids and high temperature - check the temperature limit |
| Duplex stainless / high-nickel alloy | Strongly corrosive, chloride-bearing or high-temperature specialty slurries | Corrosion resistance first; weigh service life and cost against abrasiveness |
| Polyurethane / ceramic composite | Fine but highly abrasive particles, or lightweight wear solutions | Lightweight and wear resistant, higher cost; always verify part number and dimensions |

Bore erosion, damaged sealing faces or blocked seal-water passages show up as increased leakage or abnormal packing heating.
Clean the lantern ring passages during service, confirm seal-water pressure exceeds chamber pressure and set proper gland compression.
Enlarge the exploded and construction views to confirm assembly relationships.



Part codes vary with frame and material; verify against model and part basic number before ordering.
Parts, models and manuals related to this product.
Send the model or worn-part dimensions, or call +86 188 0321 2220 / email sale@pumpq.com.
We reply within one business day. You can also call +86 188 0321 2220.
Please provide the pump model, nameplate data and duty parameters by phone or email. Performance charts and manuals can be read online.