Shijiazhuang Zhongqian Pump Industry Co., Ltd. · Slurry pumps / Spare parts / Technical support
ZQZhongqian PumpZHONGQIAN PUMP
Home/News & manuals/Slurry Pump Basic Part Number
TECHNICAL GUIDE

Slurry Pump Basic Part Number147 for the impeller · 041 for the back liner

A basic number alone cannot be ordered, and a model alone invites mistakes. The basic number, frame prefix and material suffix together make an orderable part. Below are the common numbers and a four-step verification.

Figures here come from the charts, the basic part number index and the manuals on file. Anything without a public source is marked as per supplied documents rather than inferred.

Slurry pump impeller and basic number
Slurry Pump Basic Part Number
WHAT IT IS

A basic number is a part type, not a part number

The three-digit basic number is common across the range: 147 is always the impeller, 041 always the frame plate liner. The actual order number combines a model or frame prefix, the basic number and a material or build suffix, so 147 on two pumps is not the same part.

COMMON BASIC NUMBERS

Basic numbers for wetted and seal parts

Excerpted from the basic number index on this site; each links to a part page with materials and applicable models.

Basic no.Part nameGroup
003Bearing frameDrive
005Bearing assembly / rotorDrive
013Cover plateWetted
018Front rubber sheathWetted
025End cover gasketSeal
028ExpellerSeal
029Relief coverSeal
032Casing / pump bodyWetted
036Rear rubber sheathWetted
041Frame plate liner insertWetted
043Rear sheathWetted
044Split glandSeal
062Labyrinth sleeveSeal
063Lantern ringSeal
064O-ringSeal
067Packing spacerSeal
073ShaftDrive
075 / 076Shaft sleeve / long sleeveSeal
078Stuffing boxSeal
083ThroatbushWetted
085Locating wedgeWetted
090Lip seal ringSeal
108Labyrinth ringSeal
109O-ringSeal
110Volute linerWetted
111PackingSeal
118Front lantern ringSeal
124Volute liner gasketWetted
125Frame plate liner gasketWetted
132Discharge gasketWetted
147ImpellerWetted
HOW TO LOOK IT UP

Four steps to the right part number

Identify the pump, then the frame, then the part, then the material. Skipping a step produces the wrong part.

01

Read the nameplate: model, flow, head, speed and serial number.

02

Identify the frame: the letter in the model (D in 6/4D-AH) sets shaft and bearing size and the part prefix.

03

Fix the basic number from the parts book or the index on this site.

04

Set material and suffix: choose metal or rubber from the duty, then match the suffix to the worn part.

MISFITS

Five common mismatches

FAQ

Slurry Pump Basic Part Number: common questions

Can you quote from a basic number alone?

No. It only identifies the part type; the pump model and frame code are required, or one basic number may cover a dozen part numbers.

What if the nameplate is missing?

Work back from the worn part: measure register diameter, thread pitch, sleeve bore and overall height, and photograph it clearly. Most common parts can be identified this way; special parts need drawings.

Are parts from different makers interchangeable?

Where basic number and critical dimensions match, usually yes, but material and detail differ. On critical duties, verify against the original part number.

Which parts does the index cover?

Twenty-seven routine wetted, sealing and drive parts across more than fifty basic numbers. Items not listed are identified from the parts book or a sample.

NEXT STEP

Send the model and duty; we check the part

For pumps, send medium, flow, head, density and installation. For parts, send model, frame code and basic number. We reply within one business day.

Request a quotation

We reply within one business day. You can also call +86 188 0321 2220.

Your details are used for this inquiry only.

Model and spare part identification

Please provide the pump model, nameplate data and duty parameters by phone or email. Performance charts and manuals can be read online.

Click outside or press Esc to close
☎Call✉Email⇄Inquiry