
The labyrinth sleeve uses a series of tortuous clearances to keep slurry out of the bearing chamber and lubricant in.
The labyrinth sleeve uses a series of tortuous clearances to keep slurry out of the bearing chamber and lubricant in.
On the pump side of the bearing assembly, behind the shaft seal.
Basic number, common full part numbers, the complete code index and model-by-model references.
Labyrinth sleeve / ring
—Labyrinth sleeve is 062 and labyrinth ring 108; align the ring notch along the diameter during assembly.
Part names link to their own pages; the current part is highlighted.
| Basic no. | Part name | Group |
|---|---|---|
001 | Adjusting bolt | Drive |
003 | Bearing frame | Drive |
004 | Bearing housing | Drive |
005 | Bearing assembly / rotor | Drive |
009 | Bearing | Drive |
011 | Clamp washer | Fasteners |
012 | Clamp bolt | Fasteners |
013 | Cover plate | Wetted |
015 | Cover plate stud | Fasteners |
018 | Front rubber sheath | Wetted |
023 | Front sheath stud | Fasteners |
024 | End cover | Drive |
025 | End cover gasket | Seal |
026 | Frame plate liner bolt | Fasteners |
027 | End cover adjusting nut | Fasteners |
028 | Expeller | Seal |
029 | Relief cover | Seal |
032 | Casing / pump body | Wetted |
034 | Casing bolt | Fasteners |
036 | Rear rubber sheath | Wetted |
039 | Rear sheath stud | Fasteners |
040 | Frame plate liner bolt | Fasteners |
041 | Frame plate liner insert | Wetted |
043 | Rear sheath | Wetted |
044 | Split gland | Seal |
045 | Gland bolt | Fasteners |
046 | Grease retainer | Drive |
061 | Imperial round nut | Fasteners |
062 | Labyrinth sleeve | Seal |
063 | Lantern ring | Seal |
064 | O-ring | Seal |
067 | Packing spacer | Seal |
073 | Shaft | Drive |
075 / 076 | Shaft sleeve / long sleeve | Seal |
078 | Stuffing box | Seal |
080 | Register gasket | Fasteners |
081 | Locating plate | Drive |
083 | Throatbush | Wetted |
085 | Locating wedge | Wetted |
089 | Bearing seal ring | Drive |
090 | Lip seal ring | Seal |
108 | Labyrinth ring | Seal |
109 | O-ring | Seal |
110 | Volute liner | Wetted |
111 | Packing | Seal |
117 | Spacer | Drive |
118 | Front lantern ring | Seal |
122 | Gasket | Fasteners |
124 | Volute liner gasket | Wetted |
125 | Frame plate liner gasket | Wetted |
126 | Gland stud | Fasteners |
132 | Discharge gasket | Wetted |
138 | Oil cup seat | Drive |
147 | Impeller | Wetted |
Prefixes vary with pump model and frame. Both model and part names link to their own pages.
| Impeller | E4147 |
| Volute liner | E4110 |
| Throatbush | E4083 |
| Frame plate liner | E4041 |
| Shaft sleeve | D075 |
| Lantern ring | D063 |
| Gland | D044 |
| Relief cover | DAM029 |
| Expeller | DAM028 |
| Impeller | F6147 |
| Volute liner | F6110 |
| Throatbush | F6083 |
| Frame plate liner | F6041 |
| Shaft sleeve | E075 |
| Spacer | EAM117 |
| Front lantern ring | E118 |
| Packing | F111 |
| Impeller | FAM8147 |
| Volute liner | G8110 |
| Throatbush | G8083 |
| Frame plate liner | G8041 |
| Shaft sleeve | FAM075 |
| Spacer | G117 |
| Front lantern ring | G118 |
| Impeller | G8147 |
| Volute liner | G8110 |
| Throatbush | G8083 |
| Frame plate liner | G8041 |
| Long shaft sleeve | SH076 |
| Front lantern ring | G118 |
| Impeller | EH3147 |
| Volute liner | EH3110 |
| Throatbush | EH3083 |
| Frame plate liner | EH3041 |
| Shaft sleeve | E075 |
| Spacer | EAM117 |
| Front lantern ring | E118 |
| Impeller | D3147 |
| Volute liner | D3110 |
| Throatbush | D3083 |
| Frame plate liner | D3041 |
| Impeller | THG30137LPT1A05 |
| Volute | GHG30131A05 |
| Throatbush | GHG30013LPT1A05 |
| Frame plate liner | GHG30041A05 |
Shaft seal parts control leakage between the pump chamber and the atmosphere. Packing, expeller and mechanical seal options have different seal-water requirements; check sleeve grooves and lantern ring holes first during service.
Cast iron, steel or wear-resistant alloy, often combined with a water thrower.
| Material | Typical duty | Selection notes |
|---|---|---|
| High chrome alloy Cr26 / Cr27 / Cr30 | Coarse, sharp, highly abrasive ore slurry, tailings and ash | Very hard and abrasion resistant; relatively brittle and not suited to large stray impacts |
| Natural / synthetic wear-resistant rubber | Fine particles, mildly acidic or alkaline corrosive slurry; noise and vibration damping | Elastic and resistant to fine-particle cutting; vulnerable to sharp coarse solids and high temperature - check the temperature limit |
| Duplex stainless / high-nickel alloy | Strongly corrosive, chloride-bearing or high-temperature specialty slurries | Corrosion resistance first; weigh service life and cost against abrasiveness |
| Polyurethane / ceramic composite | Fine but highly abrasive particles, or lightweight wear solutions | Lightweight and wear resistant, higher cost; always verify part number and dimensions |

Enlarged clearances, damaged teeth or packed solids contaminate the grease and raise bearing temperature.
Clean deposits, check clearances and the thrower, and replenish grease per the manual.
Enlarge the exploded and construction views to confirm assembly relationships.



Part codes vary with frame and material; verify against model and part basic number before ordering.
Parts, models and manuals related to this product.
Send the model or worn-part dimensions, or call +86 188 0321 2220 / email sale@pumpq.com.
We reply within one business day. You can also call +86 188 0321 2220.
Please provide the pump model, nameplate data and duty parameters by phone or email. Performance charts and manuals can be read online.