
The volute liner collects slurry discharged by the impeller and converts velocity energy into pressure. It is the key replaceable wear liner in a double-casing pump.
The volute liner collects slurry discharged by the impeller and converts velocity energy into pressure. It is the key replaceable wear liner in a double-casing pump.
Lines the casing to form the volute flow path, forming the pump chamber together with the liners and cover plate.
Basic number, common full part numbers, the complete code index and model-by-model references.
Volute liner
E4110F6110G8110EH3110B1110B15110Volute liner basic number 110; rubber front sheath is 018 and rear sheath 036 / 043.
Part names link to their own pages; the current part is highlighted.
| Basic no. | Part name | Group |
|---|---|---|
001 | Adjusting bolt | Drive |
003 | Bearing frame | Drive |
004 | Bearing housing | Drive |
005 | Bearing assembly / rotor | Drive |
009 | Bearing | Drive |
011 | Clamp washer | Fasteners |
012 | Clamp bolt | Fasteners |
013 | Cover plate | Wetted |
015 | Cover plate stud | Fasteners |
018 | Front rubber sheath | Wetted |
023 | Front sheath stud | Fasteners |
024 | End cover | Drive |
025 | End cover gasket | Seal |
026 | Frame plate liner bolt | Fasteners |
027 | End cover adjusting nut | Fasteners |
028 | Expeller | Seal |
029 | Relief cover | Seal |
032 | Casing / pump body | Wetted |
034 | Casing bolt | Fasteners |
036 | Rear rubber sheath | Wetted |
039 | Rear sheath stud | Fasteners |
040 | Frame plate liner bolt | Fasteners |
041 | Frame plate liner insert | Wetted |
043 | Rear sheath | Wetted |
044 | Split gland | Seal |
045 | Gland bolt | Fasteners |
046 | Grease retainer | Drive |
061 | Imperial round nut | Fasteners |
062 | Labyrinth sleeve | Seal |
063 | Lantern ring | Seal |
064 | O-ring | Seal |
067 | Packing spacer | Seal |
073 | Shaft | Drive |
075 / 076 | Shaft sleeve / long sleeve | Seal |
078 | Stuffing box | Seal |
080 | Register gasket | Fasteners |
081 | Locating plate | Drive |
083 | Throatbush | Wetted |
085 | Locating wedge | Wetted |
089 | Bearing seal ring | Drive |
090 | Lip seal ring | Seal |
108 | Labyrinth ring | Seal |
109 | O-ring | Seal |
110 | Volute liner | Wetted |
111 | Packing | Seal |
117 | Spacer | Drive |
118 | Front lantern ring | Seal |
122 | Gasket | Fasteners |
124 | Volute liner gasket | Wetted |
125 | Frame plate liner gasket | Wetted |
126 | Gland stud | Fasteners |
132 | Discharge gasket | Wetted |
138 | Oil cup seat | Drive |
147 | Impeller | Wetted |
Prefixes vary with pump model and frame. Both model and part names link to their own pages.
| Impeller | E4147 |
| Volute liner | E4110 |
| Throatbush | E4083 |
| Frame plate liner | E4041 |
| Shaft sleeve | D075 |
| Lantern ring | D063 |
| Gland | D044 |
| Relief cover | DAM029 |
| Expeller | DAM028 |
| Impeller | F6147 |
| Volute liner | F6110 |
| Throatbush | F6083 |
| Frame plate liner | F6041 |
| Shaft sleeve | E075 |
| Spacer | EAM117 |
| Front lantern ring | E118 |
| Packing | F111 |
| Impeller | FAM8147 |
| Volute liner | G8110 |
| Throatbush | G8083 |
| Frame plate liner | G8041 |
| Shaft sleeve | FAM075 |
| Spacer | G117 |
| Front lantern ring | G118 |
| Impeller | G8147 |
| Volute liner | G8110 |
| Throatbush | G8083 |
| Frame plate liner | G8041 |
| Long shaft sleeve | SH076 |
| Front lantern ring | G118 |
| Impeller | EH3147 |
| Volute liner | EH3110 |
| Throatbush | EH3083 |
| Frame plate liner | EH3041 |
| Shaft sleeve | E075 |
| Spacer | EAM117 |
| Front lantern ring | E118 |
| Impeller | D3147 |
| Volute liner | D3110 |
| Throatbush | D3083 |
| Frame plate liner | D3041 |
| Impeller | THG30137LPT1A05 |
| Volute | GHG30131A05 |
| Throatbush | GHG30013LPT1A05 |
| Frame plate liner | GHG30041A05 |
Wetted parts contact the slurry directly and wear fastest. Impeller, volute liner, front liner and frame plate liner are normally evaluated as a set to maintain running clearances.
High-chrome wear alloy, wear-resistant rubber or polyurethane: metal for coarse abrasive solids, rubber for corrosive fine particles.
| Material | Typical duty | Selection notes |
|---|---|---|
| High chrome alloy Cr26 / Cr27 / Cr30 | Coarse, sharp, highly abrasive ore slurry, tailings and ash | Very hard and abrasion resistant; relatively brittle and not suited to large stray impacts |
| Natural / synthetic wear-resistant rubber | Fine particles, mildly acidic or alkaline corrosive slurry; noise and vibration damping | Elastic and resistant to fine-particle cutting; vulnerable to sharp coarse solids and high temperature - check the temperature limit |
| Duplex stainless / high-nickel alloy | Strongly corrosive, chloride-bearing or high-temperature specialty slurries | Corrosion resistance first; weigh service life and cost against abrasiveness |
| Polyurethane / ceramic composite | Fine but highly abrasive particles, or lightweight wear solutions | Lightweight and wear resistant, higher cost; always verify part number and dimensions |

Grooves at the cutwater and discharge, deep pits, cracked lining or local breakthrough, accompanied by head loss and casing vibration.
Measure wall thickness periodically and set an allowable wear limit; on replacement verify fit with the casing and liners and the sealing faces.
Enlarge the exploded and construction views to confirm assembly relationships.



Part codes vary with frame and material; verify against model and part basic number before ordering.
Parts, models and manuals related to this product.
Send the model or worn-part dimensions, or call +86 188 0321 2220 / email sale@pumpq.com.
We reply within one business day. You can also call +86 188 0321 2220.
Please provide the pump model, nameplate data and duty parameters by phone or email. Performance charts and manuals can be read online.