Shijiazhuang Zhongqian Pump Industry Co., Ltd. · Slurry pumps / Spare parts / Technical support
ZQZhongqian PumpZHONGQIAN PUMP
Home/Products/Pump Seals
PRODUCTS · PUMP SEALS

Pump SealsPacking or mechanical seal: the choice decides how clean the pump house stays

The shaft seal is where slurry pumps differ most in daily operation. Packing is simple and inexpensive but needs flush water and accepts slight drip. A mechanical seal runs almost leak-free but demands cleaner medium, a flush plan and careful fitting.

Start with the medium. Where solids are present, a mechanical seal needs reliable clean flush water; without it the faces are destroyed quickly. Where flush water is not available, an expeller with packing is often the more dependable arrangement.

Slurry pump mechanical seal and gland parts
Pump Seals
SCOPE

What this category covers

Part / structureDescription
PackingStuffing box, packing rings, lantern ring and gland; needs flush water
Mechanical sealRotary and stationary faces with springs; low leakage, sensitive to solids
Expeller sealBack vanes generate pressure to oppose leakage, usually with packing
Seal accessoriesLantern ring, O-rings, gaskets and flush piping decide seal life
MATERIALS

Typical materials for each part

PartFunction in the pumpTypical material
Stuffing BoxThe stuffing box houses packing, the lantern ring and the gland, forming the packing seal chamber and admitting seal water for cooling, lubrication and flushing.Cast iron, cast steel or wear/corrosion-resistant alloy, with the bore matched to the shaft sleeve.
GlandThe gland compresses the packing to maintain moderate contact with the shaft sleeve and control leakage. A split design allows packing replacement without dismantling other parts.Cast iron, cast steel or stainless steel, usually of split construction.
Water Seal RingThe lantern ring sits between packing rings and distributes seal water evenly around the sleeve, forming a water film that removes heat and particles.Bronze, stainless steel or wear-resistant alloy with distribution holes.
Mechanical SealA mechanical seal uses mating rotary and stationary faces for low leakage, suiting duties where slurry dilution is not allowed or leakage is restricted. It depends on clean flush/cooling water.Faces are commonly silicon carbide or tungsten carbide; metal parts and secondary seals follow pH and temperature.
Labyrinth SleeveThe labyrinth sleeve uses a series of tortuous clearances to keep slurry out of the bearing chamber and lubricant in.Cast iron, steel or wear-resistant alloy, often combined with a water thrower.
ExpellerThe expeller generates a reverse centrifugal pressure that holds slurry back, forming a dynamic seal. At standstill or low pressure it is commonly combined with packing.High-chrome wear alloy or wear-resistant rubber, matched to the wetted parts.
SELECTION

Matching structure and material to the duty

Common combinations; grade choice needs medium temperature, concentration and particle size.

Duty conditionRecommendation
Clean flush water availableMechanical seal with a controlled flush plan
No flush water, solids presentExpeller plus packing, accepting slight drip
High suction pressureExpeller or mechanical seal to avoid pushing packing out
Corrosive mediumSelect face materials and O-ring compound for the medium
MATCHING RANGE

Matching series and models

Model pages list construction, code explanation and chart extracts.

AH series
ZJ series
ZGB series
SP series
HH series
G series
DT series
RELATED PARTS

Parts in this category

Each part has its own page with basic number, material and matching range.

FAILURE MODES

How these parts fail and what to do

Judge by wall thickness, clearance and performance, not by months in service.

FAQ

Pump Seals questions

Is a mechanical seal always better than packing?

No. Mechanical seals leak less and need less attention, but depend on flush water and cleanliness. With coarse solids and no flush water, packing with an expeller is safer.

How much drip is normal for packing?

A slight continuous drip is normal for lubrication and cooling; the manual gives the value. A sudden increase, or no drip at all, needs adjustment.

Should the sleeve be replaced with the seal?

Yes if the sleeve is grooved, otherwise the new seal will be worn by the grooves.

Inquiry

Send a model or worn-part dimensions

Parts are supplied by basic part number because the same name has different numbers in different frames. Send the pump model, frame code and a photo of the worn part, or the basic number directly.

Ask about Pump Seals

We reply within one business day. You can also call +86 188 0321 2220.

Your details are used for this inquiry only.

Model and spare part identification

Please provide the pump model, nameplate data and duty parameters by phone or email. Performance charts and manuals can be read online.

Click outside or press Esc to close
☎Call✉Email⇄Inquiry