Structure, performance and parts by series and model
Model code meaning, construction, typical duties, wetted materials and seals, wear parts, chart excerpts and sibling models, itemised for each pump.

Suction, acceleration and discharge, with wear-resistant construction for solid-liquid flow.
Slurry enters axially. The rotating impeller creates a low-pressure zone at the eye and draws the solid-liquid mixture into the casing.
The impeller vanes transfer energy to the slurry; solids gain velocity and centrifugal force and are thrown towards the volute periphery.
The volute converts part of the velocity into pressure and the slurry leaves through the discharge; wide passages reduce the risk of blockage by large particles.
The differences lie in the medium, passages, materials, shaft seal and service approach.
| Item | Standard centrifugal pump | Slurry pump |
|---|---|---|
| Medium | Clean water or low-solids liquid | Abrasive, high-density slurry containing solids |
| Impeller passage | Many vanes, narrow passages, optimised for clear-water efficiency | Fewer vanes, wide passages, prioritising clog resistance and wear life |
| Casing | Usually a single casing | Heavy duty models use a double casing: outer pressure shell plus replaceable wear liners |
| Wetted materials | Cast iron or standard stainless steel | High chrome alloy, wear-resistant rubber, duplex steel or polyurethane, selected for the medium |
| Shaft sealing | Standard mechanical seal or packing | Packing, expeller dynamic seal, cartridge mechanical seals and combinations |
Horizontal heavy duty, high head, vertical sump, submersible, gravel and special pumps.

The AH series is the heavy-duty member of the fractional slurry pump family. Replaceable metal or rubber liners sit inside the casing and cover plate, wear sections are thickened and the frames carry high loads. It is used for continuous abrasive, high-concentration slurry duty and may be staged in series within its allowable working pressure.
View models →
The HH series builds on the heavy duty slurry pump with thicker wear sections and heavier frames for higher single-stage head. It suits low-concentration/high-head or high-concentration/low-abrasion high-head duties, long-distance lines and series operation.
View models →
The ZGB series is a heavy duty, high-head pump developed for ash and slag handling. Its pump end, shaft seal and drive end can be serviced separately; it supports series staging and suits continuous abrasive duties such as power plant ash removal and long-distance tailings transport.
View models →
The ZJ series is a widely used energy-efficient abrasive-duty pump with a double metal casing and high-chrome wetted parts. The discharge can be indexed through eight positions at 45 degree intervals. It suits medium and light continuous duties in mining, power and coal preparation.
View models →
The L series keeps the design principles of heavy duty pumps but uses a higher-efficiency impeller. It runs faster and is smaller and lighter, suiting fine-particle, low-concentration or corrosive slurry and medium-low head, high-flow duties.
View models →
The DT series serves limestone-gypsum slurry circulation in wet flue gas desulphurisation. The medium is usually mildly acidic and carries crystalline solids, so both abrasion and corrosion are considered; wetted materials follow pH, chloride content and temperature.
View models →
SYA / ZJE pumps are designed for filter press feeding, where flow falls and pressure rises as the press fills. They must run stably across a wide duty range; twin-impeller or two-stage builds cover the higher pressure at the end of the cycle.
View models →
SP / SPR sump pumps keep the motor above the liquid while the pump end is immersed in a pit or tank. No foot valve, priming, shaft seal or seal water is required, suiting fixed submerged duties in settling ponds, sumps and flotation cells.
View models →
The ZJL vertical pump shares its hydraulic design with the ZJ series. Part of the pump is submerged, driven by a vertical motor through an extended shaft, suiting washery and power plant floor wash-up and pit drainage.
View models →
The ZJQ submersible slurry pump integrates pump and motor on one shaft and works fully immersed. A stirring impeller below the main impeller agitates settled sludge into suspension, suiting river dredging, sand extraction and mobile slurry removal.
View models →
G / GH gravel pumps use a single, unlined all-metal casing and a large-passage impeller for media carrying coarse gravel, pebbles or dredged sludge. GH is the high-head variant for solids too large for a conventional slurry pump.
View models →
The AF froth pump handles aerated, foam-prone flotation slurry. An enlarged suction arrangement and foam-inducing/de-aerating design reduce cavitation and loss of prime, typically in flotation circuits and chemical froth duties.
View models →
The 300LPT-SHG is a large mud circulation pump for slurry shield tunnelling, carrying spoil-laden mud between the face and the separation plant. It is characterised by a large bore and high flow and must be matched to long pipelines and the mud treatment system.
View models →Filter by code to review model designation, flow, head, speed and motor data.
Horizontal, overhung, double-casing centrifugal slurry pump Series guide →
Horizontal, double-casing, high-head heavy duty slurry pump Series guide →
Horizontal, single-stage single-suction, overhung double-casing heavy duty slurry pump Series guide →
Horizontal, axial-suction, single-stage single-suction centrifugal slurry pump Series guide →
Horizontal, single-stage single-suction light duty slurry pump Series guide →
Horizontal, single-stage single-suction FGD circulation pump Series guide →
Horizontal filter press feed pump Series guide →
Vertical, submerged, overhung centrifugal slurry pump Series guide →
Vertical, single-stage single-suction submerged slurry pump Series guide →
Dry-motor, bottom-pump submersible slurry pump Series guide →
Horizontal, single-casing, large-passage gravel / high-head gravel pump Series guide →
Horizontal froth slurry pump Series guide →
Large shield tunnelling mud circulation pump Series guide →
Clear-water performance data by series; switch between the charts below.
| Model | Max. power kW | Capacity m3/h | Head m | Speed r/min | Max. eff. % | NPSH m | Impeller mm |
|---|---|---|---|---|---|---|---|
| 1.5/1B-AH | 15 | 12.6-28.8 | 6-68 | 1200-3800 | 40 | 2-4 | 152 |
| 2/1.5B-AH | 15 | 32.4-72 | 6-58 | 1200-3200 | 45 | 3.5-8 | 184 |
| 3/2C-AH | 30 | 39.6-86.4 | 12-64 | 1300-2700 | 55 | 4-6 | 214 |
| 4/3C-AH | 30 | 86.4-198 | 9-52 | 1000-2200 | 71 | 4-6 | 245 |
| 4/3D-AH | 60 | 86.4-198 | 9-52 | 1000-2200 | 71 | 4-6 | 245 |
| 6/4D-AH | 60 | 162-360 | 12-56 | 800-1550 | 65 | 5-8 | 365 |
| 8/6E-AH | 120 | 360-828 | 10-61 | 500-1140 | 72 | 2-9 | 510 |
| 10/8ST-AH | 560 | 612-1368 | 11-61 | 400-850 | 71 | 4-10 | 686 |
| 12/10ST-AH | 560 | 936-1980 | 7-68 | 300-800 | 82 | 6 | 762 |
Particle size, density, pH and temperature differ by industry. The seven industry pages set out recommended series, wear parts and field checks.
Recommended series, wear parts and field checks
Recommended series, wear parts and field checks
Recommended series, wear parts and field checks
Recommended series, wear parts and field checks
Recommended series, wear parts and field checks
Recommended series, wear parts and field checks
Recommended series, wear parts and field checks
Open the matching model or part page; use the corner button to enlarge.
Please provide the pump model, nameplate data and duty parameters by phone or email. Performance charts and manuals can be read online.